7 best polyurethane foams

Review of the best according to the editors. About the selection criteria. The the material is subjective, is not advertising and is not serves as a guide to the purchase. Before purchase is needed consultation with a specialist.

When performing a number of construction and repairs Universal sealing material such as foam. The product is a one-component polyurethane compound, which is under pressure in the cylinder. In contact with air the composition polymerizes and hardens, forming a dense porous layer isolation. The material has good sound and heat insulation. qualities, moisture resistance, low electrical conductivity and resistance to fire. The weaknesses of polyurethane foam is sensitivity to ultraviolet rays, due to which the sealant turns yellow and collapses. In the trading network there is a huge assortment of mounting foams. To make it easier for the buyer to choose optimal composition in terms of price and properties, experts recommend considering a few points.

The main criteria for choosing foam

  1. Ordinary household foam is available in a single use, the tube is attached to the cylinder. Usually such a product is no different high density, it has a noticeable secondary expansion. Most often, such a composition is purchased to fill crevices and voids where special accuracy and accuracy are not required in work.
  2. For professionals designed foam in cylinders under special gun. The material has a high density, after drying it retains its original volume, the foam yield is significantly higher. Thanks to the gun, you can adjust the flow of the insulator, which allows you to economically spend the product. One cylinder can use several times by rinsing the gun after each application.
  3. An important characteristic of polyurethane foam is temperature interval of application. Having bought a summer squad, you can work with positive temperature from +5 to + 40 ° С. All-season product has wider operating range -10 … + 30 ° С. And for sealing joints and fill the voids in the cold it’s better to use the winter option, which withstands temperatures up to -20 ° C.
  4. On the spray foam can be found and fire marking. If the product is labeled B1, then the composition is different refractory qualities. The designation B3 indicates combustibility material. This factor is important to consider when sealing chimneys. or heating boilers.

Experts selected in our review the 7 best mounting foams. At The following criteria were taken into account when creating the rating:

  1. safety of use and operation;
  2. technical specifications;
  3. price;
  4. opinion of professionals;
  5. reviews of domestic users.

Rating of the best polyurethane foams

Nomination a place Name of product price
TOP best mounting foams 1 Penosil GoldGun 65 616 rub
2 Soudal 365 rub
3 Makroflex Standart 350 rub
4 Titan o2 430 rub
5 Ultimate te 176 rub
6 TechnoNIKOL 65 Constant 421 rub
7 Installation moment 194 r

Penosil GoldGun 65

Rating: 4.9

Penosil GoldGun 65

Penosil GoldGun 65 polyurethane foam is chosen mainly professional builders. They celebrate the perfect combination of price and Estonian product quality. Experts also note the absence shrinkage and slight re-expansion, which makes the composition predictable. Foam earned special praise from specialists for the highest output. Material finds a wide scope applications starting with the installation of window and door frames and ending with filling all kinds of voids.

According to experts, Penosil GoldGun 65 polyurethane foam deserves the highest rating for high quality, acceptable price, consistently white color and record output in volume. Foam can be criticized only for fear of low temperatures.

Advantages

  • high quality;

  • acceptable price;

  • record output in volume;

  • lack of shrinkage and secondary expansion;

disadvantages

  • at minus temperature the foam does not leave the cylinder.

Soudal

Rating: 4.8

Soudal

Not inferior to the winner of the Belgian quality rating Soudal polyurethane foam. It is fire resistant, which allows apply the composition to seal furnaces or chimneys, creating thermal sheathing or roofing. Insulator shows excellent adhesion, no shrinkage and minimal secondary expansion. After drying, the product becomes dense, a finely porous structure is formed. Experts note such foam quality, as a good output volume, durability of insulation, color retention, no cracks.

Along with good quality, wide scope and preserving the volume after drying, the material has disadvantages. The main of them, professional builders consider accelerated destruction of insulation under the influence of sunlight.

Advantages

  • wide scope of application;

  • durability;

  • dense finely porous structure;

  • thermal and fire resistance;

disadvantages

  • the destructive effects of UV rays.

Makroflex Standart

Rating: 4.8

Makroflex Standart

One of the most popular polyurethane foams in our country is Estonian product Makroflex Standart. It is used by home craftsmen, and professional builders. Hallmark of foam It has excellent adhesion to any substrate. Thanks versatility the insulator is used for different types of work, whether then foaming cracks or installing windows and doors. Stuff is good withstands temperature extremes, so that when cooling will have to run with a spray to a heat source.

The promotion of the brand played a cruel joke with him. In domestic There is an abundance of fakes labeled Makroflex on the market. Them the appearance was promoted by the high price for a quality product. Experts put foam in the third position in the ranking for shrinkage after drying.

Advantages

  • universality of application;

  • resistance to temperature extremes;

  • excellent adhesive ability;

disadvantages

  • high price;

  • shrinkage is observed after drying.

Titan o2

Rating: 4.7

Titan O2

The best option for winter use would be Polish Titan O2 polyurethane foam. The product is affordable its high quality is also confirmed by experts. But get into the top three leaders in foam did not allow consumer reviews. They note such negative qualities of the material as fragility existence outside buildings, low resistance to ultraviolet. IN The rest of the insulator deserves the most flattering words. After solidification forms a fine-meshed dense structure that does not change its volume. Foam can be used in nurseries or medical facilities due to harmlessness to the body person.

Professionals most often buy Titan O2 foam for installation windows and doors in new buildings. Over the years, isolation remains sealed and unscathed.

Advantages

  • resistance to subzero temperature;

  • lack of shrinkage;

  • affordable price;

disadvantages

  • collapses under the influence of external factors.

Ultima

Rating: 4.6

Ultima

The most affordable price boasts Ultima polyurethane foam. It is designed for domestic use, with its help you can close up cracks and voids inside and outside buildings. The product is good adhesion and rapid polymerization. Comes with a balloon convenient applicator with which you can fill in any cavities. Experts have included foam in the rating due to simplicity application, the formation of a dense layer of insulation. Rise higher assembly foam did not allow secondary expansion at 70%. The insulation layer must be reliably protected from influence. ultraviolet light.

Users highlighted a large volume of positive properties. low price and ease of use. At the same time, a high material consumption and persistent unpleasant odor.

Advantages

  • low price;

  • ease of use;

  • quick drying;

disadvantages

  • low resistance to atmospheric influences;

  • high consumption of material.

TechnoNIKOL 65 Constant

Rating: 4.5

TechnoNIKOL

Worthy competition for foreign materials is TechnoNIKOL 65 Constant domestic foam. Her strong experts call the parties universality of application, increased outlet of the insulator from the cylinder, moderate expansion. With full no shrinkage is observed upon drying; secondary expansion is in margin of error. The product is not inferior to the leaders of the rating in adhesive ability to various building materials. More often total mounting foam is used for insulation of plumbing, installation door and window blocks.

Consumers in reviews complain about the lack of domestic insulation material in the distribution network. Do not use foam with bases such as polyethylene, fluoroplastic or silicone.

Advantages

  • universality of application;

  • predictable drying behavior;

  • high yield;

disadvantages

  • shortage of sales;

  • eventually crumbles and crumbles.

Installation moment

Rating: 4.5

Moment Installation

In every Russian store with a construction bias, you can meet one-component foam assembly moment. Cylinders with insulating material is available both under the gun and single use. The most in demand is all-weather foam that is suitable for a wide range of construction and repair work. The composition is not inferior to the leaders of the rating in adhesion, after drying, a dense and uniform layer of insulation is formed. Environmentalists have not found in the material toxic or harmful to human body compounds.

A low position in our foam rating Moment Installation is possible explain a large number of fakes. Some of them have a sharp smell and not characteristic yellow color. Another counterfeit capable squeeze out the door or window frame during drying.

Advantages

  • acceptable price;

  • safety for the human body;

  • good adhesion;

disadvantages

  • a large number of fakes;

  • eventually crumbles and darkens.


Attention! This rating is subjective, is not advertising and does not serve as a guide to the purchase. Before the purchase consultation with a specialist is necessary.

Rate article
An online magazine about style, fashion, etiquette, lifestyle, and about choosing the best products and services.
Leave a Reply